Temperature

The Series TE Duct and Immersion Temperature Sensor can be used to monitor air or water temperature throughout a building management system or an air handler unit. Flanged duct sensors monitor the supply or return air and provide a thermistor or RTD output to the digital controller. Immersion sensors which are supplied with compression fittings are typically used to monitor the hot or chilled water lines throughout a building. Thermowells are recommended, but not required on the immersion sensors.
For variable air volume applications, the Series TE can be configured to have 8' plenum rated cable with flying leads. Standard units come with 4" leads with an integral terminal block to eliminate carrying extra wire nuts. For housing models, multiple knockouts provide easy conduit access to any side of the housing. The 1/4 turn lid comes with a chain to prevent it from being lost during installation.

Applications:

• Building automation
• VAV temperature sensing
• Chiller or boiler loops
• AHU monitoring

The Series TE-I Immersion Style Temperature Sensors accurately measure water temperature inside chilled and hot water loops in HVAC systems. Thermowells are required to protect the electrical connection from the process water and to allow replacement of the sensors without draining the system.

Features:

• 1/4 turn housing cover with chain to prevent dropping
• Multiple conduit knockouts for easy installation positioning
• Integral 1/2" NPSM connection for direct mounting to a thermowell
• General purpose or weatherproof enclosure options
• Terminal connection eliminates need for wire nuts

We are engaged in offering Series TE-E/N Wall Mount Temperature Sensor to our clients. Our range of all products is widely appreciated by our clients.

The compact Series 16C Temperature Controller offers accurate temperature measurement and control in a 1/16 DIN package. Designed for direct or reverse acting (cooling or heating) control, the Series 16C can be programmed for simple ON/OFF or more complex PID control functions. PID control is supported with manual or auto-tuning. Select relay, voltage or current output for control methods.
The Series 16C accepts a variety of thermocouple and RTD inputs. Process value and setpoint value are displayed simultaneously on the large dual LED. Auto-tuning, engineering units (°F or °C), and alarm status is also indicated on the faceplate. Two alarm outputs are included on the unit with 12 preprogrammed alarm functions.

Applications:

• Oven, boiler, or chiller control
• Hot plates/melt pots
• Food service equipment
• Environmental chambers
• Packaging equipment

The Series TE-A Averaging Temperature Sensors are used to measure the temperature in large ducts and air handler units. Bendable aluminum capillaries are available in 6', 12', and 24' lengths. These capillaries consist of four thermistor or RTD sensors which are internally averaged to give a single output signal. Series CC1 mounting brackets are available to mount the capillary to the wall of the duct or air handler without kinking the sensor wires inside the probe. For faster installation, the enclosure has multiple knockouts, wide mounting ears, and a screw-off captured lid.

Applications:

• Building automations
• Air handler unit monitoring
• Large air duct temperature monitoring

Features:

• Easy to mount external tab housing
• 1/4 turn housing cover with chain
• Multiple conduit knockouts for easy installation positioning

The Series TE-TNS Stainless Steel Thermowells are used to separate the instrument from the surrounding media. When used with the Series TE and TE-I Immersion Temperature Sensors, further protection is offered from aggressive media, high pressures, and flow rates while allowing for quick and easy installation of temperature sensors without having to drain process media.Thermowells are offered in both 304 and 316 stainless steel allowing for superior corrosion resistance. Fabricated, or welded, thermowells are constructed from a tube that is closed at the tip by a welded solid tip. Solid-machined thermowells are manufactured from barstock.

Applications:

• Building automation
• Chiller or Boiler Loops
• Chemical industry or process technology

Features:

• Configurable materials and sizes
• Fabricated (welded) or machined construction
• 1/2" or 3/4" NPT process connections

The compact Series 32B Temperature/Process Controller offers advanced control features for the most demanding temperature or process applications. Enclosed in a 1/32 DIN housing, the Series 32B is designed with dual, 4-digit LED displays for local indication of process value and setpoint. Control methods include ON/OFF, PID, self-tune, and manual tune. PID control is supported with 4 temperature and time (ramp/soak) control actions. The dual loop output control allows simultaneous heating and cooling control. The second output can be configured as an alarm mode using one of the thirteen built-in alarm functions.
RS-485 communications is standard on the Series 32B. Up to 247 communication addresses are available with transmission speeds of 2400 to 38,400 bps. The controller also features universal input, selectable temperature units (°F/°C), selectable resolution, quick sampling rate and security protection.

Applications:

• Oven, boiler, or chiller control
• Hot plates/melt pots
• Packaging equipment
• Environmental chambers
• Medical equipment
• Food service equipment

The Series TSW Digital Temperature Switch combines the trusted, reliable TS family of temperature controls and an installation friendly weatherproof enclosure. The bright, easy-to-read LED display shows the current output status and the temperature measurement.

Features:

• Weatherproof housing
• Single or dual stage models
• Configuration key
• Physical and passcode parameter setting protection
• TS-8T temperature probe included

The Series BTT Temperature Transmitters offer transmitter output signals with the same form and fit as our popular TE thermistor and RTD sensors for building HVAC applications. Thermowells are required when using immersion models in liquid applications.

Features:

• Duct, immersion, and outside air models available
• Radiation shield available for mounting in direct sunlight
• Transmitter output allows for longer wire runs than standard thermistor sensors

The Series BTT-E/N Wall Mount Temperature Transmitter offers transmitter output signals with the same form and fit as our popular Series TE-E/N thermistor and RTD sensors for Building Automation and HVAC installations. Duct mount, immersion and OSA models are available on the Series BTT page.

Features:

• Transmitter signal offers reliable accuracy for installations with long wire runs between the transmitter and the receiver/controller

The Series TTE Explosion-Proof RTD Temperature Transmitter is the ideal product for hazardous temperature measurement applications. The TTE series has seven preprogrammed temperature ranges that are selectable via an internal dip switch. For those applications that need a custom range, the transmitter can be easily configured for any range between -30 to 250°F with a minimum span of 40°F. The span and zero can be quickly adjusted with a simple push button design. This unit has optional listings of FM for use in Class I, Division 1, Groups B, C and D, Class II, Division 1, Groups E, F and G and Class III atmospheres or ATEX (Directive 2014/34/EU) for 2813 II 2 G Ex db IIC T6...T4 Gb (-20°C ≤ Ta ≤ + 70°C), 2813 II 1 D Ex ta IIIC T111°C Da (-20°C ≤ Ta = + 70°C) and IECEx for Ex db IIC T6...T4 Gb (-20°C ≤ Ta ≤ + 70°C), Ex ta IIIC T111°C Da (-20°C ≤ Ta ≤ + 70°C). The compact housing allows for the transmitter to be mounted in virtually any application.

Features:

• FM approved for Class I, Groups B, C, D; Class II, Groups E, F, G classified explosive environments
• Optional LCD
• Output span selected from seven common ranges or user determined

Monitor and control temperature for heating and cooling applications with the Series TS2 Digital Temperature Switch. The Series TS2 offers twelve programmable functions to customize the unit to fit application requirements. Use the 15(5) Amp SPDT relay output to drive a motor, compressor, or fan. Designed with the OEM in mind, the TS2 offers the ability to configure multiple units with the touch of a button.
Programming multiple units is quick and easy. Simply program one switch with the desired parameter settings and connect the configuration key (sold separately) to the back of the unit. Press the button on the configuration key and download the parameter settings. Connect the key to the other switches to upload the stored settings with the push of a button.
The TS2 features set point adjustments, static defrost timing, compressor mean time, hysteresis, and ambient probe adjustment. Security protection is offered using a password code. The Series TS2 Digital Temperature Switches are designed to operate with PTC (1000Ω @ 25°C) probes sold separately.

Applications:

• Refrigerators
• Chillers
• Food service equipment
• Medical sterilizers or equipment

Features:

• Simple to use temperature control device
• Configuration key

The Series TTW Immersion Temperature Transmitter combines three popular products into a single package. Our TBU series head mounted temperature transmitter is factory mounted into our A-709 enclosure. A Pt100 RTD version of our TE series is wired to the transmitter, giving insertion lengths up to 18". Each transmitter is factory programmed and calibrated to output a 4 to 20 mA signal proportional to the 32 to 212°F (0 to 100°C) temperature range.

Features:

• Preset to 32 to 212°F (0 to 100°C) output range
• USB port for easy output scale adjustment in the field